In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.Very common for a blower motor to wear out and start drawing too much current and damage the blower motor resistor or module. Some of the things that can cause blower motor not to work include: Blower motor, blower motor wiring, connectors, relay, fuse, switch/control panel, blower motor resistor, blower motor module and Ignition switch.
Where is the blower motor reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Is there a fuse for the blower motor?
Why is my blower fan not working?
If you see or hear the fan turn on, your blower motor is not the culprit. If the fan does not start, you have a wiring issue (circuit breaker trips) or motor problem (circuit breaker does not trip). While your thermostat may be at fault, only an HVAC technician can diagnose and remedy the issue correctly.
How do I know if it's my blower motor or resistor?
Typically, if the fan will work on some speeds but not on others, the resistor is suspect. Okay, let's say there's no melting going on, but your fan doesn't work on all speeds. Typically, if the fan will work on some speeds but not on others, the resistor is suspect.
How do I know if my blower motor resistor is bad?
Signs of a Bad Blower Motor Resistor Loss of HVAC fan control (total or certain speeds) The fan only works on its highest speed setting. No air coming from vents. Intermittent or inconsistent fan speed.
Where is the reset button on my carrier furnace?
Press and release the raised red button at the center of the flame roll-out switch to reset the furnace. You can press the reset button up to three times before troubleshooting the furnace's internal components or calling for repair service; allow 30 minutes between each reset.
Where is the blower motor resistor?
The heater blower motor resistor is often found beneath the dashboard. It is located in the heater and air conditioning compartment. It's connected to the air conditioning system, where it can adjust the speed of the blower motor fan. It can also be found behind the glove box of some vehicles.
What relay controls the blower motor?
The blower motor relay controls the current used to power the blower motor, and is subject to the constant on and off switching.
What happens when blower motor resistor goes out?
If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed. The heating and air conditioning systems may still function at one speed, however the resistor will have to be replaced in order for full functionality to be restored.
Where is the blower resistor located?
The blower motor resistor is usually extremely easy to access, but the hard part can be positioning your body inside the car to remove the part. The resistor is at the bottom of the HVAC housing or just behind the glove compartment.
How much does a blower motor cost?
Furnace Blower Motor Replacement Cost On average nationwide, a furnace blower motor replacement costs $400 to $600, including parts and labor. A single-speed blower motor costs around $450 to replace while a variable-speed motor costs $600 or more. You'll also need to budget labor, about $75 to $125 per hour.
What happens when a blower motor relay goes bad?
If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.
Should you replace blower motor and resistor at the same time?
We do suggest that you replace the resistor at the same time. It may not be critical, but this will keep the system more uniform. The issue may even be related to the resistor. If you know that it is not related to the issue, then you do not have to replace it.
What happens when the blower motor resistor goes out?
If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed. The heating and air conditioning systems may still function at one speed, however the resistor will have to be replaced in order for full functionality to be restored.
Will a blower motor work without the resistor?
Without any power, the motor won't run. As a result, the blower fan stays still and silent, and no air blows out of the vents. There are instances where a bad resistor will prevent the current from reaching the blower motor altogether.
How do I test a blower motor resistor?
Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.
Should I hit the reset button on my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
Where is the reset button located?
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
Where is furnace fuse located?
Fuses. If your furnace has a fuse, it will probably be located in the control box with the blower. BIf you can't locate it, the transformer may have burned up and will need to be replaced. Once you've located the fuse, check its wires to see if they're broken or look for signs of discoloration or cloudiness.
Why is my furnace running but no heat?
Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won't warm up. If the blower is running but no heat is coming out, replace the filter.
Where is the blower motor on a furnace?
One of the hardest-working parts of your home's furnace is the blower motor. In a gas forced air furnace, it's located in a box at the base of the furnace next to the air filter, where it draws return air through the filter.
Should I replace the blower motor and resistor at same time?
We do suggest that you replace the resistor at the same time. It may not be critical, but this will keep the system more uniform. The issue may even be related to the resistor. If you know that it is not related to the issue, then you do not have to replace it.
How much does it cost to replace blower motor resistor?
How much does a blower motor resistor cost? To replace the blower motor resistor, it would cost you anywhere between $50 to$150 – this includes the cost of equipment and labor. However, by doing it yourself at home, you can save up to $70.
How can I tell if a relay is bad?
You want to feel and listen for any clicks. If you feel and hear clicks, the relay works on one side – the side with the energizing circuit and coil. However, if there was no sound from the horn, the relay has a problem along the contact circuit.
Can a blower motor be repaired?
There are a number of things that can go wrong with your heating system, but if the air stops blowing altogether and the same is true on cold air settings, a blower motor replacement is likely in order. The good news is that it's a fairly straight forward repair.
Why is my blower motor not working in my car?
In this car, in the highest "4" fan speed setting, the resistor is bypassed and the blower motor is powered directly by the fan switch. That's why in some cars, the blower motor may still work in the "High" speed setting if the resistor is bad.
What happens when a blower motor resistor goes bad?
Blower motor resistor problems. The most common symptom of a failed blower motor resistor is when the heater fan only runs at high speed and doesn't work at low speeds. In some cars, a failed blower motor resistor can cause a heater fan to stop working completely. In most cases, a blower motor resistor fails due to corrosion or overheating.
What causes a heater fan to stop working in a car?
In some cars, a failed blower motor resistor can cause a heater fan to stop working completely. In most cases, a blower motor resistor fails due to corrosion or overheating.
What happens when the blower control module fails?
In most cases when a blower control module fails, the blower motor doesn't work at all. In some cars (e.g., older GM trucks), a failed blower control module or processor can cause the blower motor to continue running even with the ignition OFF.
Below you will find two interesting articles on a similar topic 👇
Which fuse is for the blower motor?What happens when the blower motor resistor goes out?
