What would cause the blower motor to stop working?

In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.Very common for a blower motor to wear out and start drawing too much current and damage the blower motor resistor or module. Some of the things that can cause blower motor not to work include: Blower motor, blower motor wiring, connectors, relay, fuse, switch/control panel, blower motor resistor, blower motor module and Ignition switch.

Where is the blower motor reset button?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

How do I know if I need a blower motor or a resistor?

Signs of a Bad Blower Motor Resistor Loss of HVAC fan control (total or certain speeds) The fan only works on its highest speed setting. No air coming from vents. Intermittent or inconsistent fan speed.

Is there a fuse for the blower motor?

Will a blower motor work without the resistor?

Without any power, the motor won't run. As a result, the blower fan stays still and silent, and no air blows out of the vents. There are instances where a bad resistor will prevent the current from reaching the blower motor altogether.

Should you replace blower motor and resistor at the same time?

We do suggest that you replace the resistor at the same time. It may not be critical, but this will keep the system more uniform. The issue may even be related to the resistor. If you know that it is not related to the issue, then you do not have to replace it.

How much does it cost to replace blower motor resistor?

How much does a blower motor resistor cost? To replace the blower motor resistor, it would cost you anywhere between $50 to$150 – this includes the cost of equipment and labor. However, by doing it yourself at home, you can save up to $70.

Where is the reset button on my carrier furnace?

Press and release the raised red button at the center of the flame roll-out switch to reset the furnace. You can press the reset button up to three times before troubleshooting the furnace's internal components or calling for repair service; allow 30 minutes between each reset.

Where is the blower motor relay fuse located?

Under the instrument panel, look under the glove box. On the right side of the fender wall you will find another fuse box. The blower motor fuse is easy to replace.

What relay controls the blower motor?

The blower motor relay controls the current used to power the blower motor, and is subject to the constant on and off switching.

How much does it cost to replace blower motor in car?

How do you know if a resistor is bad?

A good resistor should test within its rated range. A bad resistor will either show infinite resistance or a measurement far higher than its rated resistance. In either case the resistor is no longer functioning properly.

Where is the blower fan resistor located?

The blower motor resistor is usually extremely easy to access, but the hard part can be positioning your body inside the car to remove the part. The resistor is at the bottom of the HVAC housing or just behind the glove compartment.

What is the difference between blower motor and blower motor resistor?

The blower motor resistor is responsible for controlling the blower motor speed. In the past, this was done by varying the voltage supplied to the blower motor. In newer applications, the blower motor resistor is actually a solid state module that sends a varied signal to the blower motor.

How do I test a blower motor resistor?

Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.

How long does it take to replace a blower motor in a car?

How Long Does It Take To Replace A Blower Motor In A Car? It generally takes about 4 hours for an experienced technician to do a blower motor replacement. If you are doing it on your own in your garage with common tools, you can expect the job to take 6 hours or more.

How long does it take to replace a blower motor?

How long does it take to replace a blower motor? Replacing a blower motor takes 2 to 3 hours on average. The blower motor is typically located behind a control board and other furnace parts.

Should I hit the reset button on my furnace?

The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.

Where is the reset button located?

Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.

Where is furnace fuse located?

Fuses. If your furnace has a fuse, it will probably be located in the control box with the blower. BIf you can't locate it, the transformer may have burned up and will need to be replaced. Once you've located the fuse, check its wires to see if they're broken or look for signs of discoloration or cloudiness.

Why is my furnace running but no heat?

Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won't warm up. If the blower is running but no heat is coming out, replace the filter.

Where is the blower motor on a furnace?

One of the hardest-working parts of your home's furnace is the blower motor. In a gas forced air furnace, it's located in a box at the base of the furnace next to the air filter, where it draws return air through the filter.

Does a blower motor have a relay?

In a blower motor, the relay supplies the power that allows the fans to circulate warmed air. Essentially an on/off switch, the blower motor relay's reactions start and end the heating process in HVAC systems by controlling the flow of current between the power source and the motor.

How many blower motors are in a car?

The number of blower motors in your vehicle depends on its climate control system. Some cars have one blower motor, but that may not be the case for some SUVs and vans. They may have two motors, one in the heater box and another in the vehicle's rear area.

Does the blower motor resistor control heat?

The blower motor resistor is an electrical component that is a part of the vehicle's heating and air conditioning system. It is responsible for controlling the blower motor's fan speed.

How do you test a blower motor relay switch?

Connect a test light or multimeter to the ground (black lead). Turn the ignition key to the on position (engine off), and remove the relay. Using the probe, test all terminal sockets in the relay connector. Two of the four should have power.

Why is my blower motor not working in my car?

In this car, in the highest "4" fan speed setting, the resistor is bypassed and the blower motor is powered directly by the fan switch. That's why in some cars, the blower motor may still work in the "High" speed setting if the resistor is bad.

What happens when a blower motor resistor goes bad?

Blower motor resistor problems. The most common symptom of a failed blower motor resistor is when the heater fan only runs at high speed and doesn't work at low speeds. In some cars, a failed blower motor resistor can cause a heater fan to stop working completely. In most cases, a blower motor resistor fails due to corrosion or overheating.

What causes a heater fan to stop working in a car?

In some cars, a failed blower motor resistor can cause a heater fan to stop working completely. In most cases, a blower motor resistor fails due to corrosion or overheating.

What happens when the blower control module fails?

In most cases when a blower control module fails, the blower motor doesn't work at all. In some cars (e.g., older GM trucks), a failed blower control module or processor can cause the blower motor to continue running even with the ignition OFF.