• Home
  • Why do hot surface ignitors go bad?

Why do hot surface ignitors go bad?

Author of the blog (work in a car repair shop)
Ask Q

Why do hot surface ignitors go bad?

Most of the time when ignitors go bad that often it is because the ignitor is not shutting off after the gas in the furnace is ignited. If the ignitor stays on for an extended period of time this will make the ignitor short-lived.Why do hot surface ignitors go bad? Most of the time when ignitors go bad that often it is because the ignitor is not shutting off after the gas in the furnace is ignited. If the ignitor stays on for an extended period of time this will make the ignitor short-lived.

What causes hot surface ignitor failure?

How long do hot surface igniters last?

Under normal operating conditions, a hot surface igniter will last 3-5 years. During the heating season, the hot surface igniter can go through a tremendous amount of use.

Is my hot surface ignitor bad?

Your Furnace Blows Chilly Air Before going too much farther in the investigation process, make sure it's set to AUTO and HEAT. This is another symptom of a bad furnace ignitor. Again, the ignitor isn't lighting the burner and you have no combustion. Without combustion, you won't have heat!

How often do furnace ignitors fail?

How Often Should a Furnace Ignitor Be Replaced? On average, furnace ignitors will last about four to seven years. This depends upon how well maintained the system is. After the seven-year mark, you should replace it.

Can I clean a hot surface ignitor?

It is not necessary to clean a hot surface igniter as it blow off any dust. However contrary to silicon carbide ceramic hot surface ignitor which are very brittle and shouldn't be touched, silicon nitride hot surface ignitor are very robust and can be cleaned manually iff really necessary.

How long should a gas stove igniter last?

Gas oven igniters last around eight years.

How much does it cost to have a furnace ignitor replace?

Here's the bottom line: Whether for a natural gas furnace, oil, or a propane furnace, replacing a furnace ignitor–including parts and labor–will cost you around $300 – $425 for a qualified contractor to install. Compare that to, say, a draft inducer motor, which will cost $400 – $1,500 to replace.

Can hear your furnace click on but it does not fire up?

You Have a Faulty Ignition Sensor (Pilot Light) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up.

How do you know if your igniter is bad?

Your furnace won't run: The most obvious sign that your ignitor is bad is that it won't ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.

Can you clean a hot surface ignitor?

It is not necessary to clean a hot surface igniter as it blow off any dust. However contrary to silicon carbide ceramic hot surface ignitor which are very brittle and shouldn't be touched, silicon nitride hot surface ignitor are very robust and can be cleaned manually iff really necessary.

Why does my furnace flame keeps going out?

If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don't change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.

How much does it cost to replace furnace ignitor?

Are all hot surface igniters the same?

There are several hot surface igniter styles in use out there right now. Silicon Carbide, Silicon Nitride, 80 volt, 115 volt. How do I tell what I have and how do I diagnose it? The oldest hot surface used out there right now that you will encounter is the Silicon Carbide igniter.

What are hot surface igniters made of?

We manufacture and supply hot surface igniters. They are made of silicon carbide or silicon nitride, and come with ceramic bases that insulate the connected with wires. Voltages up to 240 volts are applied through the wires creating the hot surfaces used to light biomass fuels etc.

How much is a hot surface ignitor?

The cost to have the hot surface ignitor in your furnace is around $195, when out of warranty and installed by a local HVAC repair company.

Why is my furnace turning on but not igniting?

If your gas furnace initiates the start cycle but does not fire up, it's likely because of a faulty, damaged, or dirty ignitor/sensor. This is a very common furnace problem—you can try to clean the sensor and replace the ignitor.

What would cause a furnace not to ignite?

If your furnace won't ignite, the source of the issue may be a broken flame sensor. The sensor is responsible for turning off the gas burners to avoid gas buildup. Once this component starts to malfunction, it may stop the burners from igniting altogether.

Do gas stove igniters wear out?

The igniter on your gas oven is a fundamental part when it comes to heating your oven up. A gas oven igniter works by sparking and heating the gas emitted from the oven, so without it, the oven will not be able to produce heat. However, as so much rests on this little igniter, they are prone to a bit of wear and tear.

Can you clean an oven igniter?

The igniter can be cleaned like the burners on your stove top by removing it and scrubbing it with a toothbrush. Since oven cleaning often does not involve cleaning the igniter, it should be replaced if the dirt is too bad.

How much does an inducer motor for a furnace cost?

The average furnace inducer motor cost is around $245, when the part is under warranty and you pay only the labor to have it installed. The replacement cost is $465 when the warranty has expired and you pay for the furnace inducer motor.

How much is a new furnace?

A new furnace costs $1,500 to $6,500, depending on the model you choose. The average cost of installing a mid-efficiency furnace is $1,500 to $2,500. Mid-efficiency furnaces have an annual fuel utilization efficiency (AFUE) rating of 80% to 89%.

How many volts are required to properly operate a hot surface igniter?

A hot surface igniter can burn out at approximately 132 V. Even voltages in excess of 125 V may reduce igniter life. If high voltage is present, the power company should be requested to lower the power.

Are all furnace ignitors the same?

Most ignitors are interchangeable as long as they fit in the furnace space provided. Select your ignitor by looking at the one you have, and comparing it to the photos of ignitors here; select the one most similar.

Are all hot surface igniters the same?

There are several hot surface igniter styles in use out there right now. Silicon Carbide, Silicon Nitride, 80 volt, 115 volt. How do I tell what I have and how do I diagnose it? The oldest hot surface used out there right now that you will encounter is the Silicon Carbide igniter.

What is a hot surface igniter made of?

We manufacture and supply hot surface igniters. They are made of silicon carbide or silicon nitride, and come with ceramic bases that insulate the connected with wires. Voltages up to 240 volts are applied through the wires creating the hot surfaces used to light biomass fuels etc.

What causes a furnace ignitor to go bad?

Most of the time when ignitors go bad that often it is because the ignitor is not shutting off after the gas in the furnace is ignited. If the ignitor stays on for an extended period of time this will make the ignitor short-lived.

Is it common for a gas igniter to go bad?

Unfortunately, broken or malfunctioning gas range igniters are the second most frequent repair call in the appliance industry. In this article, you’ll learn about the most common gas igniter problems, why they happen, and how to prevent them.

What causes an igniter to stop working?

There are several possible causes for repeated igniter failures. One of the causes could be high supply voltage. A hot surface igniter can burn out at approximately 132 V. Even voltages in excess of 125 V may reduce igniter life. If high voltage is present, the power company should be requested to lower the power.

What is a hot surface igniter?

Silicon Carbide is one of the most common components that make up a hot surface igniter. Not only are these igniters used to light gas furnaces, but they are used for lighting stoves, boilers and other appliances that heat things around your house. Carbide is used as an abrasive, as a cutting tool, and has some automotive applications as well.

Below you will find two interesting articles on a similar topic 👇

How long does a ooze pen last?

Can you recharge a disposable vape?

Tired of looking for a video for your question?

Video Answer below 👇

Were our answers helpful?

Yes No

Thanks so much for your feedback!

Have more questions? Submit a request

FAQ for the last Day

  • Why is my heat pump blowing cold air on heat mode?
  • Your Heat Pump May Be In Defrost Mode As heat is released through the outdoor unit, it melts ice formations that would have been difficult or damaging to remove manually. Defrost mode is essentially the same as cooling mode, therefore it is likely your heat pump will blow cool air while in this mode.Why is my heat pump not blowing hot air? Problems with auxiliary heat If your heat pump isn't blowi...


  • Why does it feel like cold air blowing when the heat is on?
  • An overly clogged air filter will limit airflow to your furnace and could cause it to overheat and turn off. Then the furnace blowing cold air is all you're going to get! This is something you can check yourself – just make sure your furnace is turned off before you look at or remove the filter from the air handler.Why is cold air coming out when heat is on? The pilot light isn't functioning prope...


  • What do I do if my heater is blowing cold air?
  • Do this: Turn off your furnace at the thermostat, and check the furnace filter. If it's dirty, change it. You may need to call a technician to help you reset the furnace. Your furnace filter may be located here, next to the blower.When your furnace blows cold air, try turning the heating unit off and on. Electric heater blowing cold air: For example, your thermostat may be set to air conditioning,...


  • Why is my heat not getting hot in house?
  • Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won't warm up. If the blower is running but no heat is coming out, replace the filter.Problem: Certain parts of the house are not heating If your heater is unevenly distributing heat throughout your...


  • Why is my electric heater blowing cold air in my house?
  • More often than not, electric heaters blow cold air when its filters are clogged, and that's why it's the first thing you should check. Start by turning your heater off and inspecting the filters. If the filters are caked with dust, then it's likely the culprit behind your heater's malfunction.What does it mean when electric heater blows cold air? When a furnace only blows cold air, there's a chan...


  • How often should furnace filters be changed?
  • In most cases, you should replace your filter at least every three months -- including in summer. If you can't seem to remember to do it, a good rule of thumb is to change your furnace filter every time the seasons change.How often should you change your furnace filter in the winter? Professionals, like our team at Airco Service, Inc. say that you should change your air filter at least every three...


  • Can a dirty furnace filter cause no heat?
  • A clogged furnace air filter will negatively affect the airflow throughout your house and HVAC system. The lack of fresh air in your furnace will cause the heat exchanger to become too warm and deactivate. Dirty filters indirectly cause short cycling issues and will make it hard to keep your home warm.Lastly, dirty filters will cause your furnace and/or heat to stop heating; Dirty HVAC Air Filters...


  • Why is my furnace running but not blowing hot air?
  • Troubleshooting Furnaces Not Blowing Hot Air Check batteries of your thermostat and replace the drained or faulty one. Check the fan settings on your thermostat if they are set to “auto” instead of “on”. Make sure someone else has not set your thermostat to a lower temperature.Why is my furnace running but not blowing heat? When you turn the furnace on but no heat comes out, there may be an obstru...


Comments

Leave a Comment

<
Email us