This is a common and normal condition of a working system if the fan switch is ON. With the fan running constantly, cool air will come out whenever the set temperature is reached, and will continue to come out until the heat turns on.
Why is my Honeywell blowing cold air?
Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace's heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.
Why is cold air coming out when the heat is on?
This issue could be caused by an improper thermostat setting. Check that the fan blower switch is set to “auto” and not “on.” When the “auto” setting is chosen, the fan will only run during a heating cycle and won't push air that feels cooler through the vents in between cycles.
Why is my thermostat on heat but blowing cold air?
If your furnace is blowing cold air in your home, this is a sign of an issue with the flame detector, gas supply, air filter, pilot light, or condensate lines. Many of these issues are able to be easily solved on your own by sanitizing or replacing components in the gas furnace.
How do I fix my heat blowing cold air?
Check the Thermostat Fan Setting Outside of a heating cycle, the furnace could be blowing cold air because of a settings mistake. Go to your thermostat and take a look at the fan setting. Make sure the switch is set to AUTO, not ON.
Why is cold air coming out when the heat is on?
This issue could be caused by an improper thermostat setting. Check that the fan blower switch is set to “auto” and not “on.” When the “auto” setting is chosen, the fan will only run during a heating cycle and won't push air that feels cooler through the vents in between cycles.
Why is my Honeywell thermostat not heating?
A Honeywell thermostat won't turn on the heat because of faulty sensors, improper installation, tripped circuit breakers, etc. The heat not turning on issue on your Honeywell thermostat may be fixed by resetting the Thermostat.
Why is my furnace running but not blowing hot air?
Troubleshooting Furnaces Not Blowing Hot Air Check batteries of your thermostat and replace the drained or faulty one. Check the fan settings on your thermostat if they are set to “auto” instead of “on”. Make sure someone else has not set your thermostat to a lower temperature.
How do you reset a Honeywell thermostat?
Resetting a Honeywell Thermostat Power off the thermostat and remove the batteries. Put the batteries in the wrong way, with negative to positive and positive to negative. Wait ten seconds and put them back in the correct way. Your thermostat will be reset to factory settings.
Why is my Honeywell thermostat on cool but not working?
If the "cool on" or the snowflake icon is flashing, the thermostat is in delay mode, which can take up to 5 minutes. This delay is to protect your equipment from short cycling.
What's wrong with my Honeywell thermostat?
Look at the wiring and check if anything is loose, broken, or disconnected. Also, check to see if everything is clean. If the inside of your thermostat is filthy or there is loose wiring, that could be your problem.
Why is cold air coming out when the heat is on?
This issue could be caused by an improper thermostat setting. Check that the fan blower switch is set to “auto” and not “on.” When the “auto” setting is chosen, the fan will only run during a heating cycle and won't push air that feels cooler through the vents in between cycles.
Why is my thermostat not turning the heat on?
Check Your Thermostat If your heating system will not turn on, the first thing you should do is check the thermostat. The thermostat's battery may have gone bad, causing it to power off. If your thermostat is hardwired, a power surge, brownout, or brief power outage may have caused the thermostat to lose its settings.
Is there a reset button on a Honeywell thermostat?
Does Honeywell Thermostat Have A Reset Button? Honeywell digital thermostats don't have specific reset buttons. It will take some maneuvering to revert to the original settings on most Honeywell thermostat models. Whether programmable, non-programmable, or Wi-Fi models, each has unique instructions.
Where is the reset button on a Honeywell furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do you manually reset a thermostat?
Reset the Thermostat Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
How do I set my Honeywell thermostat to heat?
Press the "System" button to put the thermostat in Heat, Cool or Off mode. To change the setting, push the button again. The screen will display the setting you've selected. On the right side of the display, the up and down arrow buttons operate the temperature settings.
Why is my thermostat not turning the heat on?
Check Your Thermostat If your heating system will not turn on, the first thing you should do is check the thermostat. The thermostat's battery may have gone bad, causing it to power off. If your thermostat is hardwired, a power surge, brownout, or brief power outage may have caused the thermostat to lose its settings.
Does low battery affect thermostat?
Having a low battery can cause all kinds of bad readings on the thermostat, which means the thermostat may kick on when it's not supposed to, the room temperature may be incorrect, and the central system may not work at all.
Do I need to reset my Honeywell thermostat after changing batteries?
To fix the Honeywell thermostat not working after a battery change, ensure that the batteries are the correct type and are properly installed. If the thermostat still doesn't work, go for a factory reset.
How can you tell if your thermostat is not working?
The most common signs of a broken thermostat are: The thermostat display is off or is non-responsive when you try to adjust it. The display on the digital screen is faded or incomplete. The furnace or air conditioner does not respond when you adjust your thermostat.
What does the hold button on my Honeywell thermostat do?
This is where the “Hold” button on your thermostat comes into play. By pressing “Hold”, your thermostat will lock in the temperature it's currently at until you change it again. When you are ready for your normal schedule to resume, simply press the “Run” button and return to your typical programming.
How do you clean the sensor on a Honeywell thermostat?
Clean the display with a soft cloth lightly moistened with isopropyl alcohol. You can use your thermostat to improve the air quality while you're cleaning dust from around the vents or elsewhere in the house. Change the fan setting from "auto" to "on" and set the temperature low so the system blows only cold air.
Where is Honeywell thermostat temperature sensor?
The thermostat sensor is located near the evaporator coils. These coils are inside your air conditioner unit. As the air is sucked through the return vents, the air passes by the sensor and the coils. As the air passes the sensor, it reads the temperature and compares that reading to the setting on your thermostat.
Why is cold air coming out when the heat is on?
This issue could be caused by an improper thermostat setting. Check that the fan blower switch is set to “auto” and not “on.” When the “auto” setting is chosen, the fan will only run during a heating cycle and won't push air that feels cooler through the vents in between cycles.
What does the hold button on my Honeywell thermostat do?
This is where the “Hold” button on your thermostat comes into play. By pressing “Hold”, your thermostat will lock in the temperature it's currently at until you change it again. When you are ready for your normal schedule to resume, simply press the “Run” button and return to your typical programming.
Below you will find two interesting articles on a similar topic 👇
Why does my car have no heat in the cabin?Why is my heat pump blowing cold air on heat mode?
